For citation:
Radchenko V. P., Derevyanka E. E. Kinetics of residual stresses in thin-walled cylindrical specimens after bilateral surface hardening under creep conditions with rigid constraints on angular and axial linear displacements. Izvestiya of Saratov University. Mathematics. Mechanics. Informatics, 2023, vol. 23, iss. 2, pp. 227-240. DOI: 10.18500/1816-9791-2023-23-2-227-240, EDN: VGQVUH
Kinetics of residual stresses in thin-walled cylindrical specimens after bilateral surface hardening under creep conditions with rigid constraints on angular and axial linear displacements
A method for solving the problem of relaxing residual stresses after bilateral surface hardening of a hollow cylinder under creep conditions with rigid constraints on the initially specified axial deformation and twist angle is presented. The solution is developed for complex loading regimes including pure thermal exposure, axial loading, torque, internal pressure, and their combinations. A numerical simulation was conducted on a thin-walled cylindrical specimen comprised of X18N10T steel, subjected to a temperature of $T\!=\!600\,^\circ$C, with the inner and outer surfaces subjected to ultrasonic peening. The reconstruction of the initial fields of residual stresses and plastic deformations was carried out based on the known experimental information on the distribution of axial and circumferential stress components in thin surface-hardened areas on the inner and outer surfaces. A phenomenological model of creep of steel alloy X18N10T at $T\!=\!600\,^\circ$C is constructed. The rheological deformation problem within the first two stages of creep was numerically solved using time and radius discretization. The calculations established that the presence of rigid constraints on angular and linear axial displacements resulted in a decrease in the rate of relaxation of residual stresses compared to the case where these constraints are absent. Graphs illustrating the kinetics of residual stresses with respect to the sequence of temperature and loading forces at different timestamps are presented.
- Kuznetsov N. D., Tseitlin V. I., Volkov V. I. Tekhnologicheskie metody povysheniya nadezhnosti detaley mashin [Technological Methods of Enhancing Machines Components Reliability]. Moscow, Mashinostroenie, 1993. 304 p. (in Russian).
- Birger I. A. Ostatochnye naprjazhenija [Residual Stresses]. Moscow, Mashgiz, 1963. 233 p. (in Russian).
- Sulima A. M., Shulov V. A., Yagodkin Yu. D. Poverkhnostnyi sloi i ekspluatatsionnye svoistva detalei mashin [Surface Layer and Operational Properties of Machine Parts]. Moscow, Mashinostroenie, 1988. 197 p. (in Russian).
- Kudryavtsev I. V. Poverkhnostnyi naklep dlia povysheniia prochnosti i dolgovechnosti detalei mashin poverkhnostnym plasticheskim deformirovaniem [Surface Riveting to Increase the Strength and Durability of Machine Parts by Surface Plastic Deformation]. Moscow, Mashinostroenie, 1969. 214 p. (in Russian).
- Soady K. A. Life assessment methodologies incoroporating shot peening process effects: Mechanistic consideration of residual stresses and strain hardening. Part 1 – Effect of shot peening on fatigue resistance. Materials Science and Technology, 2013, vol. 29, iss. 6, pp. 637–651. https://doi.org/10.1179/1743284713Y.0000000222
- Terres M. A., Laalai N., Sidhom H. Effect of nitriding and shot-peening on the fatigue behavior of 42CrMo4 steel: Experimental analysis and predictive approach. Materials & Design, 2012, vol. 35, pp. 741–748. https://doi.org/10.1016/j.matdes.2011.09.055
- Pavlov V. F., Kirpichev V. A., Vakulyuk V. S. Prognozirovanie soprotivleniia ustalosti poverkhnostno uprochnennykh detalei po ostatochnym napriazheniiam [Prediction of Fatigue Resistance of Surface-Hardened Parts by Residual Stresses]. Samara, Samara Scientific Center of the Russian Academy of Sciences Publ., 2012. 125 p. (in Russian).
- Pavlov V. F., Bukaty A. S., Semenova O. Yu. Prediction of the endurance limit of surface-hardened parts with stress concentrators. Vestnik Mashinostroeniya, 2019, iss. 1, pp. 3–7 (in Russian). EDN: VTAEPK
- Majzoobi G. H., Azadikhah K., Nemati J. The effects of deep rolling and shot peening on fretting fatigue resistance of Aluminum-7075-T6. Materials Science and Engineering: A, 2009, vol. 516, iss. 1, pp. 235–247. https://doi.org/10.1016/j.msea.2009.03.020
- Starcev N. I. Truboprovody gazoturbinnykh dvigatelej [Pipelines of Gas Turbine Engines]. Moscow, Mashinostroenie, 1976. 272 p. (in Russian).
- Radchenko V. P., Berbasova T. I., Tsvetkov V. V., Saushkin M. N. Mathematical modeling of relaxation of residual stresses in thin-walled pipelines in the delivery state and after bilateral surface hardening at creep. PNRPU Mechanics Bulletin, 2013, iss. 3, pp. 117–128 (in Russian). https:/doi.org/10.15593/perm.mech/2021.3.11
- Derevyanka E. E., Radchenko V. P., Tsvetkov V. V. Relaxation of residual stresses in a surface-hardened cylinder under creep conditions and rigid restrictions on linear and angular deformations. Mechanics of Solids, 2020, vol. 55, iss. 6, pp. 898–906. https:/doi.org/10.3103/S0025654420660024
- Radchenko V. P., Pavlov V. F., Saushkin M. N. Mathematical modeling of the stress-strain state in surface hardened thin-walled tubes with regard to the residual shear stresses. PNRPU Mechanics Bulletin, 2019, iss. 1, pp. 138–150 (in Russian). https://doi.org/10.15593/perm.mech/2019.1.12
- Radchenko V. P., Tsvetkov V. V. Kinetics of the stress-strain state of surface hardened cylindrical specimen under complex stress state of creep. Journal of Samara State Technical University, Series Physical and Mathematical Sciences, 2014, iss. 1 (34), pp. 93–108 (in Russian). https://doi.org/10.14498/vsgtu1313
- Radchenko V. P., Kocherov E. P., Saushkin M. N., Smyslov V. A. Experimental and theoretical studies of the influence of a tensile load on the relaxation of residual stresses in a hardened cylindrical specimen under creep conditions. Journal of Applied Mechanics and Technical Physics, 2015, vol. 56, iss. 2, pp. 313–320. https://doi.org/10.1134/ S0021894415020170
- Radchenko V. P., Tsvetkov V. V., Saushkin M. N. Residual stress relaxation in a hardened cylinder under creep, loaded by an axial force, torque and internal pressure. Journal of Applied Mechanics and Technical Physics, 2020, vol. 61, iss. 4, pp. 583–592. https://doi.org/10.1134/S0021894420040124
- Sherafatnia K., Farrahi G. H., Mahmoudi A. H., Ghasemi A. Experimental measurement and analytical determination of shot peening residual stresses considering friction and real unloading behavior. Materials Science and Engineering: A, 2016, vol. 657, iss. 7, pp. 309–321. https://doi.org/10.1016/j.msea.2016.01.070
- Xie L., Wang Ch., Wang L., Wang Z., Jiang Ch., Lu W., Ji V. Numerical analysis and experimental validation on residual stress distribution of titanium matrix composite after shot peening treatment. Mechanics of Materials, 2016, vol. 99, pp. 2–8. https://doi.org/10.1016/j.mechmat.2016.05.005
- Gallitelli D., Boyer V., Gelineau M., Colaitis Y., Rouhaud E., Retraint D., Kubler R., Desvignes M., Barrallier L. Simulation of shot peening: From process parameters to residual stress fields in a structure. Comptes Rendus Mechanique, 2016, vol. 344, iss. 4, pp. 355–374. https://doi.org/10.1016/j.crme.2016.02.006
- Zimmermann M., Klemenz M., Schulze V. Literature review on shot peening simulation. International Journal of Computational Materials Science and Surface Engineering, 2010, vol. 3, iss. 4, pp. 289–310. https://doi.org/10.1504/ijcmsse.2010.036218
- Lebedev V. A., Chumak I. V. Kinetic model of hardening of the surface layer of parts by vibro-impact PPD methods. Strengthening Technologies and Coatings, 2008, iss. 7, pp. 3–8 (in Russian). EDN: JWEXDN
- Radchenko V. P., Pavlov V. F., Berbasova T. I., Saushkin M. N. The method of reconstruction of residual stresses and plastic deformations in thin-walled pipelines in the delivery state and after bilateral vibro-shock surface hardening with a shot. PNRPU Mechanics Bulletin, 2020, iss. 2, pp. 123–133 (in Russian). https://doi.org/10.15593/perm.mech/2020.2.10
- Mozharovskaya T. N., Mozharovsky V. N., Stefan N. I. On the dependence of the time to destruction and the steady rate of creep deformations of structural materials. Journal of Mechanical Engineering NTUU “Kyiv Polytechnic Institute”, 2010, iss. 59, pp. 37–40 (in Russian). EDN: VAXUEV
- Samarin Yu. P. Uravneniia sostoianiia materialov so slozhnymi reologicheskimi svoistvami [Equations of State of Materials with Complex Rheological Properties]. Kuibyshev, Kuibyshev State University Publ., 1979. 84 p. (in Russian).
- Radchenko V. P., Eremin Yu. A. Reologicheskoe deformirovanie i razrushenie materialov i elementov konstruktsii [Rheological Deformation and Fracture of Materials and Structural Elements]. Moscow, Mashinostroenie-1, 2004. 265 p. (in Russian).
- 1290 reads